To cut Rexin fabric neatly at home, mark the backing, keep the material flat and cut one layer at a time with sharp fabric scissors or a rotary cutter. Test your tool on an offcut first, include the required seam allowance and keep the sheet still rather than pulling it towards the blade.
Which tools should you use to cut Rexin?
Rexin usually has a PVC or polyurethane surface over a textile backing. Its thickness, stretch and backing affect how it cuts, so test your tool on a small piece rather than choosing it based only on how the surface looks.
- Sharp fabric scissors: Use a pair that cuts cleanly through the full thickness without chewing up the backing. Dressmaking shears with a lower blade that rests on the table help you keep the sheet flat.
- Rotary cutter and mat: Use these for long straight cuts and broad curves. Choose a blade size you can control comfortably; a smaller blade is easier to steer around tighter curves.
- A ruler suitable for rotary cutting: Use a non-slip ruler thick enough to guide the blade. Keep your fingers well away from the edge you cut along.
- Removable marking tools: Try tailor’s chalk, a fabric pencil or another marker you’ve tested on the backing. You’ll also need a tape measure and a paper or card template.
- Pattern weights and clips: Use smooth weights to hold templates down and, where needed, place clips within the seam allowance. Avoid pins through visible areas because they leave holes.
Avoid blunt household scissors and serrated kitchen scissors, which can leave crushed or uneven edges. If you use a rotary cutter, work only on a suitable cutting mat, never directly on a table, floor or glass surface.
Keep your free hand out of the blade’s path and close or retract the blade before putting the cutter down. The Canadian Centre for Occupational Health and Safety recommends cutting away from your body when using knives and cutting tools; reposition the material rather than cutting towards yourself.
How to prepare Rexin for cutting
Unroll the material on a clean, flat surface large enough to support the piece you need. Allow any loose curls to flatten before measuring, and support overhanging material so its weight doesn’t pull the sheet out of shape.
Don’t stretch Rexin flat or press it with a hot iron to remove creases. Heat can damage the coating. If you stretch the material while measuring, your cut piece may shrink back or become distorted when you release it. Position your pattern away from severe creases wherever possible.
Check the surface for scratches, thin patches and coating defects. For matching panels, keep the grain, printed design and direction of stretch consistent; otherwise, adjoining pieces may look different or stretch differently once you stitch them together.
Plan to cut one layer at a time, especially with slippery, thick or stretchy material. Folding and cutting two layers together can save time, but the layers can shift and leave you with mismatched edges.
How to mark Rexin before cutting
Mark on the backing wherever possible, using light pressure. Test your marking tool on an offcut and check the coated side too: ink can show through or spread, while a hard pencil can leave an impression.
For most home projects, place the Rexin backing upwards while tracing. Before cutting this way, test whether your tool leaves a clean coated edge underneath. If the surface chips, catches or drags, try cutting with the coated side upwards, using a removable marking tool you’ve tested or a weighted template.
Trace the finished pattern accurately, then add the seam allowance before cutting if the pattern doesn’t already include it. Follow the project instructions rather than choosing an allowance at random. Mark the cutting line clearly so you won’t confuse it with the stitching line.
Label the backing of each piece with its name, direction and matching points. For a left and right pair, turn the template over for the second piece. If you keep the template the same way round for both cuts, you’ll get two identical shapes rather than a mirrored pair.
How to cut straight lines and curves in Rexin
- Secure the template or marked sheet with smooth weights placed clear of the cutting path. Check that the material lies flat beneath the ruler.
- For straight cuts with a rotary cutter, align the ruler with the cutting line and roll the blade away from your body with steady pressure. Avoid sawing backwards and forwards.
- With scissors, keep the lower blade close to the table and use long, controlled strokes. If closing the tips fully leaves small steps along the edge, stop just before they meet.
- For curves, use shorter strokes and turn the sheet gradually while keeping it supported. Choose scissors for tight curves if you can’t steer the rotary cutter accurately.
- At corners, stop precisely where the lines meet. Reposition the sheet and make the next cut separately rather than swinging the blade around the corner.
- Check that you’ve cut through the backing completely before lifting the piece. Snip any remaining threads instead of pulling the cut edges apart.
If a rotary blade repeatedly leaves fibres uncut, check whether it’s blunt and whether your mat is badly grooved. Pressing harder can reduce your control; replace a worn blade according to the tool’s instructions.
How to tidy Rexin edges after cutting
Lay each piece flat beside its template and check corners, curves and matching edges. For paired pieces, compare them without stretching either one. Trim only obvious excess, keeping the intended seam allowance intact.
Remove loose backing fibres with small, sharp scissors. You usually don’t need to neaten an edge that sits inside a seam. For a visible edge, you may need binding, a folded finish or an edge-finishing product specifically compatible with your Rexin.
Never seal edges with flame or use uncontrolled heat to smooth them. You risk damaging the coating and backing rather than improving the cut.
If you cut slightly outside the line, trim back carefully. If you cut inside it, check whether the remaining seam allowance still meets the project requirements. Recut the piece if the mistake changes its finished size or leaves too little material for a secure seam.