Rexin is usually water-resistant, not necessarily waterproof. Some grades have coatings that prevent water penetration under specified test conditions. Check any waterproof Rexin claim carefully: an intact coated sheet may keep water out, but a stitched cover, bag or seat can still leak through seams, edges and damaged areas.
What makes Rexin water-resistant?
Rexin is a common trade term for artificial leather, usually made with a PVC or polyurethane coating over a fabric backing. The coating gives it a leather-like appearance and forms the main barrier against liquid water. The backing supports the material but does not necessarily repel water.
On an intact surface, a small spill generally stays on top long enough for you to wipe it away. This makes suitable upholstery grades practical for dining chairs, seating and other surfaces you need to clean regularly. It doesn't mean you can soak the material or leave water standing on it indefinitely.
Distinguish between surface water resistance and the ability of the whole item to prevent leaks. Water-resistant material withstands some exposure. For a waterproof claim you can rely on, check the test conditions and whether the claim applies to the sheet alone or the finished product.
Is PVC Rexin more water-resistant than PU?
PVC-coated Rexin generally provides a good barrier against liquid water when its coating is continuous and undamaged. You'll commonly find it sold for wipe-clean upholstery and protective uses. However, a thin or poorly bonded PVC coating can still fail through wear, cracking or separation from its backing.
You can't judge PU artificial leather by the material label alone. Some PU coatings resist spills well, while microporous versions allow moisture vapour to pass through. Breathability and resistance to liquid water are different properties, so don't assume that breathable material will leak or that every PU grade is waterproof.
Some PU formulations can also deteriorate through hydrolysis, a chemical breakdown involving moisture. Resistance depends on the formulation and construction. If you expect repeated exposure to damp conditions, ask for hydrolysis resistance data as well as water-penetration results. Neither softness nor thickness proves that a material is suitable.
Where can water get into Rexin products?
Water doesn't enter only through the top surface. Before you buy or reuse a Rexin item, inspect the places where its protective coating ends or has punctures.
- Stitch holes and seams: A needle punctures the coating, and ordinary stitching doesn't make the joint watertight.
- Cut edges and exposed backing: Fabric can absorb water and carry it towards padding, lining or other absorbent layers.
- Cracks and peeling patches: A broken coating exposes the layers below and no longer forms a continuous barrier.
- Zips and fastenings: Water may enter around closures even when the surrounding sheet resists penetration.
- Folds and worn corners: Repeated flexing and rubbing can weaken the coating, particularly at points that get heavy use.
You may also find it difficult to dry water trapped beneath Rexin because the coated face restricts evaporation through that side. If a seat feels damp underneath despite a dry-looking top, check the seams, underside and padding rather than wiping only the visible surface.
Can you use Rexin for outdoor covers?
You can use a suitable Rexin grade for outdoor covers, but don't assume ordinary indoor upholstery material will do. Ask for a grade intended for that use, with suitable resistance to light exposure, repeated flexing and water penetration. The cover's design matters as much as the sheet.
For a furniture protector or equipment cover, choose a design that lets water drain rather than collect in depressions. You may need a compatible sealing method for stitched joints. Welding can produce watertight joints in suitable coated fabrics, but the results depend on the material, equipment and workmanship.
For bags, check the lining, zip construction and seam treatment before relying on their water protection. For seating, protect the foam and underside as well as the upper face. Don't assume that a spill-resistant seat cover will keep its cushion dry during prolonged exposure to water.
Avoid standing water unless the supplier specifically rates both the material and the finished product for it. Don't use Rexin sold for upholstery as a substitute for a purpose-made tank liner, waterproof membrane or product rated for immersion.
How do you check a waterproof claim?
Ask for the product specification and a test report for the exact grade you plan to buy. Tests for coated fabrics can measure resistance to water penetration under pressure. ASTM International publishes ASTM D751, which covers test methods for coated fabrics. Don't accept a reference to a standard alone as proof of a passing result.
- Confirm whether the claim covers the coated sheet or the finished, stitched item.
- Request the test method, result, units and conditions, including any exposure time or applied pressure.
- Check whether the tests used new material or material that had undergone flexing, abrasion or ageing.
- Ask which seam-sealing methods and cleaning products the supplier approves.
For a simple check, place a spare offcut over a dry absorbent cloth, put a little water on its coated surface and check underneath. This may reveal obvious leakage, but a droplet test is limited: it can't establish long-term performance, pressure resistance or the reliability of seams.
How should you dry wet Rexin?
Blot spills promptly with a soft cloth. To remove dirt, use a damp cloth and, if the care instructions permit it, a small amount of mild soap. Wipe away the residue without flooding seams or exposed edges, then dry the surface.
If water reaches the backing or cushion, open removable covers where practical and let air circulate around all damp parts. Avoid direct heaters, hot hairdryers and aggressive rubbing. Don't close or refit a cover while its backing or padding remains damp.
You generally don't need a waterproofing spray on intact coated Rexin. A spray may change its colour, feel or finish without sealing stitch holes or repairing cracks. Use only a treatment approved for that specific material and test it on a concealed patch. If the coating is peeling or splitting, replace the material or have it professionally repaired.
Sources
- ASTM International · ASTM (astm.org)